04-23-2007, 02:48 PM
i cant keep it idleing it just dies im not sure what the problem is it was running good then whenever i hit the breaks or slow down to a stop it would die. oh well time for a new engine any ideas its for a 1/10 truck
![Confused Confused](https://www.chitownrc.com/images/smilies/confused.png)
![Confused Confused](https://www.chitownrc.com/images/smilies/confused.png)
![Confused Confused](https://www.chitownrc.com/images/smilies/confused.png)
![Confused Confused](https://www.chitownrc.com/images/smilies/confused.png)
![Confused Confused](https://www.chitownrc.com/images/smilies/confused.png)
![Confused Confused](https://www.chitownrc.com/images/smilies/confused.png)
![Confused Confused](https://www.chitownrc.com/images/smilies/confused.png)
![Confused Confused](https://www.chitownrc.com/images/smilies/confused.png)
i think my motor is done
|
04-23-2007, 02:48 PM
i cant keep it idleing it just dies im not sure what the problem is it was running good then whenever i hit the breaks or slow down to a stop it would die. oh well time for a new engine any ideas its for a 1/10 truck
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
04-23-2007, 02:49 PM
goat 585 has 2 hpi 12s for $75
04-23-2007, 02:54 PM
Check your clutch and clutch bell bearings. If they hang up, it's just like snubbing the flywheel to a stop.
04-23-2007, 02:58 PM
ill look into that
im going to tear the truck apart tommarow. i took it apart last night and rebuilt it and i went to test ti and the problems happend ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
04-23-2007, 03:02 PM
maybe the engine isnt sealed correctly could that be a problem also
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
04-23-2007, 03:09 PM
Make sure everything is tight on the engine. Tighten down the head bolts in start pattern so they all get tightened evenly. Check the back plate and carb sinch bolt.
FS-Sportwerks 1/8 Hauler
04-23-2007, 03:42 PM
If you rebuilt it, then that means that you just need to put the trim for your throttle servo so it won't move the carb when you hit the brakes, then you will need to turn your idle up on the carb.
8ight | Mini-T | CEN Boat | Stampede | JR R-1
ALL RC STUFF FOR SALE. PM FOR DETAILS.
04-23-2007, 03:48 PM
DAVEC-NITRO-RS4 Wrote:Check your clutch and clutch bell bearings. If they hang up, it's just like snubbing the flywheel to a stop. well you get the cookie when i put the clutch nut on i used threadlock and it seeped out and on the the bearings and the bell housing. who knows what breaks down threadlock and also when i got the nut off i destroyed the collet on the shaft so now i need to get everything that is stuck together apart and try it again. im still going to order an extra motor i think there is more to it than what i just found ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
04-23-2007, 05:01 PM
thanks guys i got everything freed up and now it runs decent i need to figure out why it runs so hot im in the 240-270 range and when i richen it up it still is hot
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
04-23-2007, 06:09 PM
Do you have a vent hole cut in the body? Geared to low?
8ight | Mini-T | CEN Boat | Stampede | JR R-1
ALL RC STUFF FOR SALE. PM FOR DETAILS.
04-24-2007, 10:21 AM
Why not bring your car up to Cary Illinois and Ill help fix it?
04-24-2007, 12:45 PM
240-270 is ok
What king of crank shaft does your truck run? threaded crank (little stubby) or a longer pilot (SG) shaft?
Mugen MBX5T
RBS5 RB2045 Futaba 3PM Hitec 5955, 5965
04-24-2007, 01:45 PM
270 is totally fine... maybe a bit warm for a .12 tho on the other hand.
04-24-2007, 01:57 PM
its the standard shaft its not the cut standard its the long threaded. but not the sg.
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
Port and polished motor | Edward Rc | 1 | 3,268 |
11-08-2009, 10:14 AM Last Post: DAVEC-NITRO-RS4 |
|
2nd motor back from propinch | eraser | 83 | 28,055 |
05-29-2008, 01:54 PM Last Post: Thirdgen89GTA |
|
eletric motor turns to RPM's.......... | bob1961 | 4 | 5,408 |
03-28-2008, 08:24 PM Last Post: bob1961 |
|
Which motor | hansarvin | 134 | 24,441 |
01-23-2008, 11:25 AM Last Post: J-Dub |
|
question about a new motor | eraser | 20 | 5,016 |
10-14-2007, 12:39 AM Last Post: willitbme15 |
|
My new motor | rocco79 | 34 | 7,396 |
04-22-2007, 10:32 AM Last Post: Meatwad |
|
what motor? | AddictedtoNITRO | 10 | 2,999 |
03-26-2007, 10:38 PM Last Post: HAGASAN |
|
2.5T electric motor? | Gforce | 1 | 1,650 |
02-05-2007, 01:39 AM Last Post: Czech-it-Out Graphics |
|
elec motor | AddictedtoNITRO | 14 | 3,502 |
10-23-2006, 11:48 PM Last Post: mikeh |
|
which motor?? | kevinF | 39 | 6,574 |
09-28-2006, 11:12 AM Last Post: kevinF |