Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Lhr 2/19/06
#51
There were tons of people having problems yesterday. They guy next to me left without being in one qualifier and another guy I know needed a part for his Maxx. Don't get discouraged by problems, out of the three trucks I brought I was lucky that one was working.

I'm so glad I got the tuning issue figured out!!

Tex, I'll remember to put a hole in the body for fuel Smile
Reply
#52
UEmaxx, we all get frustrated sometimes. Your still a beginner, don't get discouraged so easily.

One of the reason why your truck breaks all the time is because you wreck all the time, and I know why. I was watching you in a couple of your Quals/Race and you are trying to go too fast. Slow down and instead of trying to be so fast, try and just be smooth and flowing. If you can't hit the double in front of the drivers stand 80% of the time, don't try and clear it! You will break. You don't need to SKY off the tabletops, that's not the fast way around.
Next time you come out Steve, I will take your truck around the track a few times and see how it drives then give you some track/driving tips that will help you out. Smile
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply
#53
Most of my problem is my steering. I don't what it is. I am using the servo that came with the DX3. I have to take the tight turns slow. I am not going to spend $100 or more on a good servo. Instead I am most likely putting it towards another vehicle.

Another is my shocks. You felt them yesterday. I don't want to dump anymore money into this truck.
FS-Sportwerks 1/8 Hauler
Reply
#54
Tex Wrote:UEmaxx, we all get frustrated sometimes. Your still a beginner, don't get discouraged so easily.

One of the reason why your truck breaks all the time is because you wreck all the time, and I know why. I was watching you in a couple of your Quals/Race and you are trying to go too fast. Slow down and instead of trying to be so fast, try and just be smooth and flowing. If you can't hit the double in front of the drivers stand 80% of the time, don't try and clear it! You will break. You don't need to SKY off the tabletops, that's not the fast way around.
Next time you come out Steve, I will take your truck around the track a few times and see how it drives then give you some track/driving tips that will help you out. Smile

listen to tex, steve.
he told me the same thing, I kept breaking but then he watched me run a few laps and he said to slow down and drive smooth.

believe it or not when I was doing that I started to pass people up. also you arent any faster in the air. your wheels are what push your car but when you have all 4 wheels in the air then all you have is air resitance which slows you down. you cant control your ride to good in the air.

just keep practicing.

I am not saying im a pro because hell I have only been there 3 times, but by listening to tex and other guys at the track I have learned a lot.
Losi 8ight with v-spec[SIZE="4"]
[/SIZE]
Reply
#55
I go really slow and I noticed two things, a) people run into the back of me and usually knock their own RC over and b) I was able to drive around a lot of accidents Smile

One person did tell me that I hit the wall way to much at the end of the strait but it's hard to see with the marshall standing in the way, I need to learn how to use my brakes much better.

UEMaxx a Hitec 645 is relatively inexpensive.
Reply
#56
I hear that people say Hitec's are junk.

I also have the problem of my truck eating spurs. After the main my brand new spur has NO teeth left. I don't know what that problem is either. Mesh is good and and the engine isn't moving. I backed off the slipper 1/2 a turn.
FS-Sportwerks 1/8 Hauler
Reply
#57
what chassis do you have?
Losi 8ight with v-spec[SIZE="4"]
[/SIZE]
Reply
#58
I've been using the Hitec 645 for a long time, I only had one that would only turn one way and Towers replaced it.

I need to grind the carriers on the new Savage, I don't even way to touch the engine tuning right now, it seems to be just right.
Reply
#59
I just wanted to say that I had a great time at the track yesterday. I meet alot of new people that seemed like a great group of people, and I got me a couple of good starting setups for my cars. Thanks again for all the tips and info guys can wait to race with you all.
"I'm always amazed to hear of air crash victims so badly mutilated that they have to be identified by their dental records. What I can't understand is, if they don't know who you are, how do they know who your dentist is?"
Reply
#60
traxxas thrasher Wrote:what chassis do you have?

Predator. It's not chassis flex.Big Grin
FS-Sportwerks 1/8 Hauler
Reply
#61
Just go slow. As Mike Czech would say "Slow is fast". (And everyone else would I just remember him telling me) When I chilled I was turning fast and consistant lap times in stock form. I got a tad antsy with the new motor and if I went through the turns at all quick it would push like crazy... Slow down and you will be fine. If you need to roll a jump do it. It's better than breaking...
Reply
#62
UE-Maxx Wrote:Predator. It's not chassis flex.Big Grin

maybe alignment between CB and spur???? Maybe it's just a tiny bit crooked?
got paint?
Colors by Dave - CBD
1-29-07 ... you know.
Reply
#63
DAVEC-NITRO-RS4 Wrote:maybe alignment between CB and spur???? Maybe it's just a tiny bit crooked?

IDK maybe. I haven't ate a spur ever since I got the new chassis (about 3 gallons) and I shredded (sp) two yesterday.
FS-Sportwerks 1/8 Hauler
Reply
#64
Were you pitting near Gabe?
got paint?
Colors by Dave - CBD
1-29-07 ... you know.
Reply
#65
Sort of. I was at the end of the table on one side and he was maybe 2 seats in on the other side like 2 rows away.
FS-Sportwerks 1/8 Hauler
Reply
#66
DAVEC-NITRO-RS4 Wrote:Were you pitting near Gabe?

haha:bustingup
dont start that again.

this just in traxxas spur gears have dramatically dropped in sales or whatever you said, that was funny.


ue-maxx maybe you trans is moving?
Losi 8ight with v-spec[SIZE="4"]
[/SIZE]
Reply
#67
See, if you get too close to his truck, yours will strip the spur also, out of empathy for his.....Rolleyes
Reply
#68
hahaha, hey leave gabe alone hes cool.

dave you crack me up
Losi 8ight with v-spec[SIZE="4"]
[/SIZE]
Reply
#69
ok, for you.

"psycho" is how it's spelled....that's been bugging me....
Reply
#70
LOL Dave

It only happened before the last qualifier and during the main.
FS-Sportwerks 1/8 Hauler
Reply
#71
DAVEC-NITRO-RS4 Wrote:ok, for you.

"psycho" is how it's spelled....that's been bugging me....

ohh I didnt see that thanks.Rolleyes
Losi 8ight with v-spec[SIZE="4"]
[/SIZE]
Reply
#72
there now its changed
Losi 8ight with v-spec[SIZE="4"]
[/SIZE]
Reply
#73
I have ran 10 tanks through my truck on the track at race speed and the spur looks new. All it took for that problem to go away was to loosen the slipper.

UE maxx, your springs that you are using on your truck are WAY too stiff. You want Trinity Black in the rear and Trinity baby blues in front...Toss those navy blue ones, too stiff.

Also the Hitec servos only break if you don't set the end points correctly with the radio. Basically it's people using cheap AM radios with no adjustments that run into trouble. If you set the end points right the 645MG should last a long time.

It takes many race days and tons of practice time to get a good setup and to build your RC up to take the abuse you give it. It's not going to happen in 3 race days. It took me about a year before I even raced and another year to get half way decent.

UEmaxx if you think a different RC is going to make your race days more enjoyable, your dead wrong. Practice and patience is key.
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply
#74
dude tex ur truck looks freakin dialed out there man, u gotta hook up with jesse and get a center diff in that thing. If it wasnt for lap traffic I think the race would have been much closer
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply
#75
Thanks Mike!
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)