Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
(RC) Real Street Drags Sat. Oct.23rd
#26
im not even gonna try and run against big blocks for drag racing. Il stick to racing them on the track were i can stand a better chance at beating them. Six with that 28 should slaughter the big block competition for sure. Il stick to trying to beat gabe again. hasnt worked yet but il eventually do it someday.
Reply
#27
lol.. yeah and of course since I'll have the .28 apart for the non pull start setup I might as well do a bit of modding too. Its going to be scary. hehe..
-- John --
1:1.. 01 Z28 Camaro A4 Sure.. its stock.
1:8's.. K3, Inferno GT, and a straight line beater car
1:18.. RC18t Mamba and 3s lipo
Reply
#28
aahhhhhhhhhhhh dang. Oh well, I'll still give'em he!! on the blacktop.
I may have to consider a home made wheelie bar to keep the front end on the ground so I can accelerate with the whole motor not having to baby it off the line.
Reply
#29
well I dont think it gunna be by the White Castle , they destroyed the parking lot .
LAst night we were in teh Kohls parking lot which is in the same mall just further south . Its really flat and nice for drag racing . One problem , there is a Retirement Village right there (OLD PEOPLE) so the days activites should proilly die down earlier than normal ( early 10pm normal 2 am)
Gino was also talking about Prarie State College parking lot to hold the event , I will be talking with him later today about it
Cant wait Big Grin Big Grin Big Grin

Hey any of you guys goin to the RC show in Rosemont? Oct 16 - 17 (sat sun) I am going on Sunday with another guy we are leaving Lansing about 11am to go
If its too loud your too old

If you cant be an athlete , be an athletic supporter .
Reply
#30
We are all going to the hobby show on Saturday. meeting in the front at 10am or so.

Keep us posted on the new location for the 23rd street drags. I wanna make sure I'm there Smile
Reply
#31
yeah you to have the RCRSD's now. I'm all hyped to drop that .28 into the landmax. Plus I got some new goodies dirt cheap on ebay for the landmax. Smile
-- John --
1:1.. 01 Z28 Camaro A4 Sure.. its stock.
1:8's.. K3, Inferno GT, and a straight line beater car
1:18.. RC18t Mamba and 3s lipo
Reply
#32
Six, what class would you race in with the LM? 1/8 on-road? or Buggy? It wouldn't be against MT's, would it?

What Pipe are you going to run with the .28 in the landmaxx? low end or high end pipe? I bet you'd do 200ft pretty quick. A low end pipe might get you there quicker?
Reply
#33
now that was alot of questions Smile
Reply
#34
Hmmm... don't know. I'd get mopped up by 1/8 on roads because they are much lighter and have better traction than the landmax. probably with the 1/8 buggies because essentially the landmax is just a buggy. no on the MT's but I could get wheel wideners and drop MT wheels on.. lol.

I don't know on the pipe. I'm going to do some testing next weekend. I'm going to measure out 200ft in the parking lot I run in. Ohhh also I got a mini wireless camera and made a mount for the landmax. I'll get some wicked in car footage with it. lol.. its also fun to strap to the mini-t and drive all over the house just sitting in my room.. lol!
-- John --
1:1.. 01 Z28 Camaro A4 Sure.. its stock.
1:8's.. K3, Inferno GT, and a straight line beater car
1:18.. RC18t Mamba and 3s lipo
Reply
#35
hmmm.. did some tinkering with the landmax, OPS .21, SH 86 pipe, firioni sliding clutch, 17t clutchbell, and 200ft. I need to get the landmax off the line a lot faster so a bit of clutch tuning is in order but I'm going to leave it because the .28 has sooo much more low end so I'll wait. Hopfully I'll get the .28 in the Landmax and see how quick it is this week. I tried the torque pipe.. and it limits RPM too much and RPM is needed on the big end. hehe.. mabey over the winter I'll build another .21 rear drive RS42. I already know how to make it work and make it stick.
-- John --
1:1.. 01 Z28 Camaro A4 Sure.. its stock.
1:8's.. K3, Inferno GT, and a straight line beater car
1:18.. RC18t Mamba and 3s lipo
Reply
#36
just rear drive? I dont see how that would be possible without spinning out , unless your talking about gooping the tires with VHT or something or are you gunna put the 1/8 scale Serpent rear tires on your HPI?
If its too loud your too old

If you cant be an athlete , be an athletic supporter .
Reply
#37
He can explain better but, he makes a drag car out of a RS4. wide foams out back and so fourth
Reply
#38
Its all about traction, suspenson, and downforce. It took a while but I got it to work and work well. basically 2wd makes its a lot lighter, easier, and simpler. I found 4wd to be a waste for just going fast in a straight line anyhow because the front tires spin easily wasting power and the front always seemed to break easily. Then drop on some tall and fat rear foams, and large front and rear wings to keep it planted, soft rear suspension. It won't spin out at all. I was running a hyper 8 port on an RS4 2. all modded and set up nothing like stock with no front driveine at all. I basically got i all worked out so it stuck incredibly well and went like stink then the crystal vibrated loose and it went into a curb at high speed and I junked it after that. If I can get another RS42 cheap I'll do it again. I started to build a .21 RS4 3 but I had serious doubts on making it work reliably.
-- John --
1:1.. 01 Z28 Camaro A4 Sure.. its stock.
1:8's.. K3, Inferno GT, and a straight line beater car
1:18.. RC18t Mamba and 3s lipo
Reply
#39
you still got that picture of your old RS42 that was bent up in the front?
Reply
#40
ohh yeah.. I forgot about the pics..


Here is the initial RWD only setup.

After this I got a nice rear wing on it and was running a junk accord body on it. then I dumped the body totally and ran a large spoiler on the front to keep the nose down and got the 1/10 truck foams on the rear and moved the RX pack to the nose.

Then just as a I got it all dialed... well yeah it lost a game of tag with a curb when the crystal vibrated loose and fell out.

[Image: crash_01.jpg]

[Image: crash_02.jpg]

I wish I had more pics along the way of my setups but I know what I need to do anyhow.. its all in my head.


I'm seeing a NovaRossi .28 powered RS42 based drag car in my head. hehe...
-- John --
1:1.. 01 Z28 Camaro A4 Sure.. its stock.
1:8's.. K3, Inferno GT, and a straight line beater car
1:18.. RC18t Mamba and 3s lipo
Reply
#41
its just a little bent its still good, its still good lmao. WOW. Wish i could have seen that crash
Reply
#42
WOW, how fast was that thing going when it kissed the curb?
Reply
#43
well the week before I had it radared by a cop at 58 mph. I was full throttle ripping across the lot and the crystal came out it continued at full throttle until jus before it the curb. the RX pack and other pieces were found around 30 or 40 feet away! It was brutal.
-- John --
1:1.. 01 Z28 Camaro A4 Sure.. its stock.
1:8's.. K3, Inferno GT, and a straight line beater car
1:18.. RC18t Mamba and 3s lipo
Reply
#44
This time, throw a little tape over the crystal... lol
Reply
#45
no fail-safe? $20.00 would have saved you a lot of money. lol
Reply
#46
That same $20 would have caused alot of trouble too. give and take
Reply
#47
actiually there was an electrinc failsafe on there. I was using my futaba AM radio gear which was the only radio gear I have that failsafes work well with but it didn't do squat because a failsafe only saves you from a loss of power. Failsafes are just about useless imo. Also I got the car for free in the first place.. lol.
-- John --
1:1.. 01 Z28 Camaro A4 Sure.. its stock.
1:8's.. K3, Inferno GT, and a straight line beater car
1:18.. RC18t Mamba and 3s lipo
Reply
#48
SixVi6-Camaro Wrote:well the week before I had it radared by a cop at 58 mph. I was full throttle ripping across the lot and the crystal came out it continued at full throttle until jus before it the curb. the RX pack and other pieces were found around 30 or 40 feet away! It was brutal.

TheNewGuy witnessed some thing like that...i think it was the 1st time i went to berwyn, ripping up and down the parking lot with my tec...i never knew thet the 4-tec was a gymnists...in all the rols and flips i lost the crystal some where...but now that i think of this it has nothing to do with this topic...oh well...it was funny!
Ofna 9.5.. RB Concepts WS7 II -For Sale
Ofna 9.5 Roller - For Sale
Savage...ALL ALUM, bran new Mach427 -For Sale
message me, im, or email if intersted open to just about all offers.
Reply
#49
that pic looks like a tin can lid after its been opened. hard to believe that it could hit and stick with enough force to rear it up like that.
Reply
#50
yeah and not seen in the pic.. because I could not find it after the crash.. was a 1/4" thick AL brace with large ball ends at either end that tied the front to the center of the chassis. It was just gone after the crash. you could see where the screws had ripped clean out of its mounting points but I could never find that brace. I bet it was bent good. when it hit that curb it didn't bounce, spin, flip, or anything. just went crack.. dead stop.
-- John --
1:1.. 01 Z28 Camaro A4 Sure.. its stock.
1:8's.. K3, Inferno GT, and a straight line beater car
1:18.. RC18t Mamba and 3s lipo
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)