Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
WANTED! Motor...
#26
Time for better driveshafts then...
Reply
#27
Czech-it-Out Graphics Wrote:swap the bearings with some novas and the mill will last u gallons

The one I will be getting has them in it. Big Grin
Reply
#28
Mikey, he said he only has 130 bucks to spend ... The bearings will be 80 alone!
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#29
I just bought a V-spec with the Nova bearings 1/2 gallon on it for $130. :joy: :joy:
Reply
#30
FreeRideJunkie Wrote:I just bought a V-spec with the Nova bearings 1/2 gallon on it for $130. :joy: :joy:


awsome! bye bye clutch.
SOLD: BCE Pro X1-CRT Truggy, Dace Predator/Unlimited Engineering towered VBS Supermaxx
Current: Nitro Traxxas Slayer Pro 4x4, Nitro Traxxas Slash
Reply
#31
I plan on getting a nice 3-shoe when I buy the conversion... if not then very shortly there after. I think it will be fun... I just want to wheelie like Gabe. LoL
Reply
#32
And I mis-typed... I guess it is the VZB Non turbo. Therefore it is not the V-spec but still a powerhouse with nice bearings. Still not a bad deal IMO...
Reply
#33
be carefull with those, some of them had a crappy p/s like sonny ran one for 8 gallons other guys ran them for 2 and they died lol
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply
#34
i bet thats nice to know AFTER ya bought it! LOL!
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#35
Well 2 is still more than I got out of the 2.5 LoL... Well I will run this untill it dies. When it does I will rob it of the bearings and find someone selling a v-spec. Hehehehe....
Reply
#36
In the end I will have a full .21 setup with a pretty nice motor, a new clutch, and pipe for about $200. I think I will be fine...
Reply
#37
NICE i looked at that engine today Cool
Go Fast Or Go Home
Reply
#38
And what did you think/decide??
Reply
#39
It was nice it will be faster than any 2.5 any day Big Grin i have 2 brand new turbo v-spec's in my room or i would have got it
Go Fast Or Go Home
Reply
#40
rocco cant keep up j/k
Go Fast Or Go Home
Reply
#41
What?? wit who???
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#42
i can keep up till about half way down the straight away. Against gabes p5 i can keep up the whole time. But then again buggy gearing and mt gearing a really different ratio's
[Image: mich1iy1.jpg]
Reply
#43
My xtm is plenty fast
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#44
i was just playing with u guys Big Grin
Go Fast Or Go Home
Reply
#45
im not sayin its a bad mill I love OS's I hope it last u a long time
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply
#46
If it doesn't last me at least a couple gallons I will be burning something down with my nitro fuel. LoL... J/K

So how should theis motor be geared?? Right now the gearing on the truck is stock...
Reply
#47
Not sure of EXACT gearing, but it will have a LOT more torque. To offset this, you want to go with a smaller CB and a larger spur.
Reply
#48
Yeah... I was wondering what would give me the best balance of pop off the line (I know I will have plenty) and speed. Further suggestions...
Reply
#49
dan u want the opposite, larger CB smaller spur, a smaller cb will give u even more torque as will a larger spur
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply
#50
LoL... that is what I meant that I knew. I know what affect gearing has as I need to do it on mountainbikes. Kind of assumed it was typed correctly. Oops. LoL
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Slash roller, phoenix roller, xl-5, brushless motor and more cubsfan7658 0 3,845 09-30-2012, 07:46 PM
Last Post: cubsfan7658
  Wanted: EMAXX chicagokenji 0 1,907 12-20-2010, 01:34 PM
Last Post: chicagokenji
  Slash or Crawler wanted TexMexSu 3 2,827 12-14-2010, 09:38 PM
Last Post: TexMexSu
  .28rr axial motor w/ ofna 086 pipe PMHOURS 2 2,090 02-25-2010, 11:27 PM
Last Post: PMHOURS
  Wanted bargen 2.4g radio reciver spazzzattak 1 1,961 02-25-2010, 01:33 PM
Last Post: firesprink281
  Wanted trade/buy 3.3 tmaxx tranny spazzzattak 0 1,793 02-19-2010, 02:40 PM
Last Post: spazzzattak
  1:1 Motor rocco79 0 1,685 01-17-2010, 10:54 AM
Last Post: rocco79
  GT2 Brand New O.S. 18 Motor tcase 1 1,884 09-20-2009, 12:05 AM
Last Post: tcase
  wtb-motor? Racin' Ranger1 4 2,217 07-14-2009, 11:22 PM
Last Post: Racin' Ranger1
  WTB:1/18 Mamba Brushless Motor maxximum_44 0 1,524 06-30-2009, 12:30 AM
Last Post: maxximum_44

Forum Jump:


Users browsing this thread: 1 Guest(s)