Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
2nd motor back from propinch
#26
i dont think so mick.
Hi im johnny knoxville and welcome to jackass
Reply
#27
then stick to your clamp and stove lmao
Reply
#28
eraser Wrote:then stick to your clamp and stove lmao

He wasn't replying to you, he was replying to Mike's post a few posts up.
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Reply
#29
Not too sound rude...

But how about ya take some pics of his work.... You keep sayin how sweet it is, now id like to see it with my own two eyes
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#30
+ 123456789

GS RACING, TQ FUEL, FASTLANE GRAPHIX, CZECH-IT-OUT
Reply
#31
Rocco, just send in your Axial .38 and see for yourself. Im about ready to send in my Racers Edge .32 soon.
T-T-T Confusedalute:
Reply
#32
i sent a pair of my STS .28's.....we will see how his dremel does on those.....Wink

GS RACING, TQ FUEL, FASTLANE GRAPHIX, CZECH-IT-OUT
Reply
#33
no doubt, open one up and show the mods, I would like to see
Reply
#34
Lmao
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#35
the site has no info on the "modding" I tried to call him with no luck Sad I left a message and will call again tommarow as I need my engine pinched prior to the next pro series race which is in about a week and half
Reply
#36
osrocket...
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply
#37
yeah I used osrocket like 2 yrs ago with good luck, I just like trying new people/things
Reply
#38
no pics on site at all
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#39
so what exactly is pinching? ive been reading this thread and never got what it was.
Reply
#40
a process that can in take a motor that is worn out and lacks compression and renews it and adds a couple gallons to the life of the motor....

As long as the sleeve and pistion dont have gouges or serious blems most worn p/s will benefit from a pinch ...

I think you can only pinch a motor like 3 times though
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#41
shit u can pinch a motor for ever, run it till it blows baby!!!
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply
#42
motoxer4life Wrote:so what exactly is pinching? ive been reading this thread and never got what it was.

they basically make the top of the sleeve a tighter fit so it has more compression
Losi 8ight with v-spec[SIZE="4"]
[/SIZE]
Reply
#43
hell czech had an rb that jimmy pinched so many times its only an 18 now.
i think im gonna send this guy my cen 46, is that legal for 1/8 buggy at that pro series yall talk about
Hi im johnny knoxville and welcome to jackass
Reply
#44
Zing!!!
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#45
never recieved a call back from them today... thats strike one in my book
Reply
#46
Might as well just buy the new reciprocating assembly. ( P/S. Conrod Wristpin and Clip)

At least that's what I'd do...but I guess that's expensive.

Would you say you racers pinch your 'expensive' motors a couple times instead of rebuilding them?
Reply
#47
yea cuz its stupid to rebuild it cuz it cost about as much as a brand new one so why bother
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply
#48
I wanted him to modd mine as well though...
Reply
#49
Czech-it-Out Graphics Wrote:yea cuz its stupid to rebuild it cuz it cost about as much as a brand new one so why bother


After the life of the engine is done...do you then rebuild it after it;s been pinched? I've not gone through many motors, Im just curious what you would do.
Reply
#50
not many do, alot of times if you are sponsored you can send in your used shit an they will rebuild it for you either for free or pretty cheap. But when my dad had the access to the machines to do pinching i pinched them light until they just didnt run as well. At that point most of my motors had 10 gallons on them so they were for parts or to sell with a roller on ebay. Usually the bearings are good and the case is always good to have for back up etc. pinching is pretty much ur best bet, break it in again (lightly) then after about a gallon or so throw in a new rod and it will last you a long time
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Port and polished motor Edward Rc 1 3,140 11-08-2009, 10:14 AM
Last Post: DAVEC-NITRO-RS4
  you know your back into r/c when.....? grim digger 13 6,353 06-19-2009, 11:38 AM
Last Post: Thirdgen89GTA
  propinch.com is incredible please read eraser 7 5,996 05-29-2008, 05:21 PM
Last Post: Czech-it-Out Graphics
  eletric motor turns to RPM's.......... bob1961 4 5,203 03-28-2008, 08:24 PM
Last Post: bob1961
  Which motor hansarvin 134 21,545 01-23-2008, 11:25 AM
Last Post: J-Dub
  question about a new motor eraser 20 4,474 10-14-2007, 12:39 AM
Last Post: willitbme15
  i think my motor is done cheesecake 16 3,712 04-24-2007, 01:57 PM
Last Post: cheesecake
  My new motor rocco79 34 6,542 04-22-2007, 10:32 AM
Last Post: Meatwad
  what motor? AddictedtoNITRO 10 2,713 03-26-2007, 10:38 PM
Last Post: HAGASAN
  2.5T electric motor? Gforce 1 1,538 02-05-2007, 01:39 AM
Last Post: Czech-it-Out Graphics

Forum Jump:


Users browsing this thread: 1 Guest(s)