Mini-T, Tl-01, E-Zilla, and a Haro Mirra 540 for sale/trade

[AznRacer]

i got an all aluminum mambafied mini-t that needs some fixing to be sold, TL-01 drifter, just ran recently, works great, and an e-zilla that needs new motors. specs for each car

1. Mini-T (taken from my RCU Ad, may sound a lil funny lol)

I have a mini-t for sale or trade. It has a mamba 8000kv, hitec fm aggressor, Thunder power 1320mah 2 Cell pack, and a hitec HS-81MG servo. I can sell it as a roller, or sell it with the electronics. The electronics have some problems, such as a burnt mamba motor and an old lipo battery (careful...)The mamba motor can be sent to Castle Creations to be replaced. Price of that fix will be $40 in M/O or Check (price was given to me by a CC costumer service person). It is all aluminum, hop-ups to the max. The car has been put through its courses, bashed hard. but almost none of the aluminum bends or breaks. The bottom rear of teh chassis has damages, due to a couple stripped hexheads that was installed wrong when i first bought (just a cosmetic damage, does not affect performaance whatsoever. Here is a list of the parts I have put into this truck.

1. FullForceRC Aluminum Chassis

2. FullForceRC Aluminum Chassis Brace

3. Dynamite Aluminum (almost all the aluminum parts in the truck are aluminum_

-Aluminum parts include front and rear a-arms, front shock tower, gearbox, c-hub, steering knuckles, front bulkhead, lower chassis, front and rear pivot block, steering setup, Bumper, etc... (rear shock tower is plastic, metal is prone to bending)

4. Rubber sealed bearings- REALLY good bearings, unknown brand.

5. Racers Edge Oil shocks w/ a bunch of optional springs

6. Racers Edge TurnBuckles- Super BEEFY (there is a mixture of GPM turnbuckles in the truck)

7. Racers Edge Suspension Hinge Pins- no e-clips needed

8. Integy Carbon Fiber Steering Plate

9. Team Losi CVDs- slight bend in one of them

10. Team Losi Dual Disk Slipper and extra gear (I think I still have an extra one , not sure though)

11. Trinity Monster Off-Road, rear tires are bald(ing) :p

12. Custom Wing (used an extended body post setup and a wing from an on-road nikko toy).

13. HEXCREWS screw set. sizes are 1.5mm and 0.05"



There are some minor problems with the car:

1. Tranny bearings are wearing down, should be replaced.

2. Differential is stock. I locked it using silicon. Upgrade to ball is recommended ($20).


Electronic problems

1. Burnt motor; can be sent back to Castle Creations with $40 and be replaced for a NEW one.

2. lipo pack is old, recommend to change to a new pack (nimh or lipo)





The HS-81MG servo is almost new, Mamba 25 ESC is fine, but may need some touch ups (i.e. wiring)



EXTRAS (if bought RTR)

1. MANY spare parts (not really spare, but some stock parts that were thrown into the toolbox since I upgraded to aluminum)

2. If a good price/trade is made, I could give my CELECTRA 1-3 Cell Lipo Charger WITH a 3A power supply. ($75 value)

3. Paddle Tires on Black rims (never used, but glued)

4. Bodies: Orange Parma Buggy Body, White Escalade body, White w/carbon fiber stock body.



If you have questions, just post it here or e-mail me at [email protected].



Estimated prcies

RTR- $330

ARR- $ 230


Trades are welcome, I am interested in a nitro. Monster trucks (LST), buggies, Stadium Truck (XXX-NT), or any other cars you post, I may be interested. I will post new things about this car if it happens to pop up in my head. THANKS FOR LOOKING!












http://www.rcuniverse.com/market/item.cf...electric=0




Heres my TL-01

1. LRP AI Waterproof ESC
2. Venom 19t motor
3. Spektrum servo
4. Hot Bodies/HPI Radio and reciever
5. 2000mah 6 cell nicd pack
6. Tamiya lightweight chassis
7. Tamiya speed tuned gear
8. duratrax ball bearings
9. TLT-1 rear dogbones
10. ABS on nikko 12mm rims.

$100 for car with electronics, $70 for roller (negotiable)







will trade TL-01 for burshless electric car/truck or nitro (or nitro engine .21 and up)




E-Zilla

been broken for a while, so im guessing the batteries are dead (dead dead). the motors are dead, so basically your getting a roller with an ESC and a servo. if my other deal doesnt come by, i will include the stock radio. the only mod it has is savage shock and spring, fan for esc, maxx 14mm dishes, and deans plugs.







my bike, Haro Mirra 540 is for sale for $350 NO TRADES (unless its a Fly Bike )

has Maxis Barely Legal Rear rim, Fat Claw Chain, Polished cranks (thanks to bamf90, i had to put this on here so he doesnt complain lol), i forgot what grips it had, but all i know is that its Primo and it has a barcode design, Oddessey Slic Linear brake cable, aftermarket pads, TOONA rear tire.







selling for no less than $350, but may be negotiated. i need to buy my friends bike for $400.







THANKS FOR LOOKING! PICK-UP ONLY, UNLESS DEAL WITH!