davec in XRC mag? - Printable Version +- ChitownRC (https://www.chitownrc.com) +-- Forum: Open Forums (https://www.chitownrc.com/forum-5.html) +--- Forum: Off-Topic (https://www.chitownrc.com/forum-14.html) +--- Thread: davec in XRC mag? (/thread-4046.html) |
davec in XRC mag? - Tex - 07-18-2006 I'm reading page 201 in the July issue of XRC. One of the 'ask the professor' questions is asked by a guy named davecnitoS4 and I'm wondering if it's you Dave? davec in XRC mag? - FreeRideFrosty - 07-18-2006 Can't be. Who needs to ask magazines when you have this forum??? LoL davec in XRC mag? - Tex - 07-18-2006 he might have asked in the XRC forum? davec in XRC mag? - DAVEC-NITRO-RS4 - 07-18-2006 yep...they had a hard time typing out the whole screenname. Asked it on their forum months ago. davec in XRC mag? - FreeRideFrosty - 07-18-2006 What was the question/answer?? And clear out your PM's o' famous one. davec in XRC mag? - DAVEC-NITRO-RS4 - 07-18-2006 Buy the magazine.... will do.... http://www.rc411.com/forum/showthread.php?t=1920&highlight=facts davec in XRC mag? - firesprink281 - 07-18-2006 smart-aleck! davec in XRC mag? - DAVEC-NITRO-RS4 - 07-18-2006 what? davec in XRC mag? - DAVEC-NITRO-RS4 - 07-18-2006 ok...nevermind... davec in XRC mag? - Tex - 07-18-2006 so did you know you made it into the mag? davec in XRC mag? - rusty savage - 07-18-2006 sweet pick out tex. good general question dnrs4! pretty cool it made it to a mag! davec in XRC mag? - DAVEC-NITRO-RS4 - 07-19-2006 Tex Wrote:so did you know you made it into the mag? yep, saw it there, too. It took me a while to notice it, though. That page was kind of distracting I asked that question to them when we were all discussing it here.... davec in XRC mag? - salsaking - 07-19-2006 cool it made it to the mag, wow it takes a long time for it though. davec in XRC mag? - DAVEC-NITRO-RS4 - 07-19-2006 Derek B said: "It doesn't matter what percentage you use or change to. The thing that matters is that the engine is shimmed correctly. Your engines instructions generally tell you what it's shimmed for. Going up in percentage will make you have to add a shim, while going down will make you take one out. Having less compression, going from 30% o 20% will not harm the engine. Having it shimmed for 20% and going to 30% might cause higher temps and blown plugs. You don't have to "re-break" in the engine, but remember to retune. Just richening it up so you don't run too lean is all you need to do, and retuning for the new fuel." Can't recall all the answers I got here..... davec in XRC mag? - Tex - 07-19-2006 Derek Buono is right but he's not god as he makes himself out to be davec in XRC mag? - DAVEC-NITRO-RS4 - 07-19-2006 Yeah, he doesn't really ask or clarify if the process is the same for small block or big block engines. I was more curious to hear what the answer would be from an "industry guy" at a magazine. davec in XRC mag? - Tex - 08-28-2006 Hey Dave your in the October issue now, pg.28 I was lol, that page was funny as hell. davec in XRC mag? - DAVEC-NITRO-RS4 - 08-28-2006 In there twice...see the Professor section page 183! |