08-25-2005, 04:47 PM
The truggy is just sitting and gathering dust I've decided to sell it. since the showme showdown its just sat on the shelf all dirty and still the the broke shock end and loose motor mount. I have no motovation to work on it so I fixed the front shock and went through it today.
I'm selling it as a rolling chassis just as you see it in the pics below. I partially dissasembled it and cleaned the major parts. this is a Kanai 2 truggy with an Al rear brace, Lunsford Ti front brace, Al C hubs in the front, Universals all round, Ti front turnbuckles. I installed Hot Bodies Lighting Satdium Pro Ring and Pinion gears (10/43 Vs. standard buggy 13/43 ring and pinions) so you can run standard buggy 13t clutchbell with the large tires no problem. You can also easily run buggy tires and raise the CB to a 16 tooth making it a simple CB, tire, and body swap away from running Unlimited and 1/8 buggy classes with the same RC. Servos (stock Futaba and JR 590), RX pack, and 2 bodies as well as the wheels shown are included. With some good grippy tires and a big ol' .28 on board this truggy would rip around the track.
the only known problems are a slightly tweaked front shock tower, and the wing is barley holding on.
to run it will need radio gear, engine, header, pipe, and motor mounts. (motor mounts that were on there were striped so I tossed them.) It has served me well and the only problems I had was a broken front shock from forgeting to set the front droop and a broken rear arm from jumping it at a CSRC event and landing on the right rear on a jump which sent it 40ft into the air. lol.
Also adding the set of Panther KDLP tires's on yellow Dom wheels as seen in my Sig.
I'm asking $200 obo for it. No trades. It goes on fleabay on sunday night if it doesnt' sell. Thanks for looking!
Pics..
![[Image: truggy_01.jpg]](http://home.comcast.net/~pewter_camaro/truggy_01.jpg)
![[Image: truggy_02.jpg]](http://home.comcast.net/~pewter_camaro/truggy_02.jpg)
![[Image: truggy_03.jpg]](http://home.comcast.net/~pewter_camaro/truggy_03.jpg)
![[Image: truggy_04.jpg]](http://home.comcast.net/~pewter_camaro/truggy_04.jpg)
![[Image: truggy_05.jpg]](http://home.comcast.net/~pewter_camaro/truggy_05.jpg)
I'm selling it as a rolling chassis just as you see it in the pics below. I partially dissasembled it and cleaned the major parts. this is a Kanai 2 truggy with an Al rear brace, Lunsford Ti front brace, Al C hubs in the front, Universals all round, Ti front turnbuckles. I installed Hot Bodies Lighting Satdium Pro Ring and Pinion gears (10/43 Vs. standard buggy 13/43 ring and pinions) so you can run standard buggy 13t clutchbell with the large tires no problem. You can also easily run buggy tires and raise the CB to a 16 tooth making it a simple CB, tire, and body swap away from running Unlimited and 1/8 buggy classes with the same RC. Servos (stock Futaba and JR 590), RX pack, and 2 bodies as well as the wheels shown are included. With some good grippy tires and a big ol' .28 on board this truggy would rip around the track.
the only known problems are a slightly tweaked front shock tower, and the wing is barley holding on.
to run it will need radio gear, engine, header, pipe, and motor mounts. (motor mounts that were on there were striped so I tossed them.) It has served me well and the only problems I had was a broken front shock from forgeting to set the front droop and a broken rear arm from jumping it at a CSRC event and landing on the right rear on a jump which sent it 40ft into the air. lol.
Also adding the set of Panther KDLP tires's on yellow Dom wheels as seen in my Sig.
I'm asking $200 obo for it. No trades. It goes on fleabay on sunday night if it doesnt' sell. Thanks for looking!
Pics..