The General Paint Thread

[Ponch]

I waited about 10-15 mins and that didn't happen... But I didn't wait for all of it to dry, and I hair dryed it.

[Obsessive R/C]

Are you painting on it right away after it seems dry?? I've always let mine sit at least overnight to fully dry (even after they turn clear) I also use a heat gun to dry in between colors...the moisture in the paint (if your using waterbased paint like Createx or Faskolor) may actually be softening up the last layer of LMF.

[Biodragen]

I too have never dealt with that.

I use a heat gun in between coats.
I use a brush and not a sponge and with each coat
I also alternate direction of application.
I do this 3-4 times.
Then I cut a triangle in an area that I don't have to worry about and pull from the center. If I get it up without breaking I am good--if not it needs another coat.

Since I started doing this---I have had no more LMF issues when pealing it offand it is much easier than it being to thin which sounds like you are thin.

Just my thought on it

[DAVEC-NITRO-RS4]

Maybe that first coat needs to be heavier, and then the rest can be thinner?

[Biodragen]

Originally Posted by Revo2k

I waited about 10-15 mins and that didn't happen... But I didn't wait for all of it to dry, and I hair dryed it.

You should wait until it is all clear first before you apply the next coat.
If you don't let it dry all the way and keep piling it on there will be spots that just will not dry very well.
Use a hair dryer in betwwen coats but afer 3-4 and I also let it sit overnight.

[Czech-it-Out Graphics]

the thicker the better. let each coat dry overnight or like everyone said let it turn clear before you even think of putting on the next coat. Each sucessive coat takes longer and longer to dry. I have the advantage of being able to mask say 10 bodies at once and while they are drying work on another 5 etc so it is easier for me to be patient and that the crap dry.

[UE-Maxx]

I do let it sit over night before I start to paint. Looks like it is thick coats and drying over night on my TC3 body.

Thanks

[Ponch]

Ok, so start with a barely there, thin coat one day, and then slap LMF on it at 9pm the next day, go to school the next day, and do another coat before bed for 3 or 4 days?

[Czech-it-Out Graphics]

ya basically, i usually do 5 coats. put it on like you would a coat of paint like ur painting a wall or something make sure its all covered, but dont glob it on there.

[UE-Maxx]

Thanks.

I'll put up some pictures of two mini bodies I finished a little while ago tomorrow.

I need to wait on the TC3 body to see where to mark the body post holes.

[Obsessive R/C]

I use a good quality 2 1/2" paint brush (a nice one like you use for trim in a house) pour in a blob about the size of a half dollar and paint away...three nice even thick coats just like that...works great. Probably get 3-4 bodies out of a 4 oz. jar

[Ponch]

You guys use the window masks that come with the body and LMF over them, or no masks, just lmf everywhere? Thanks.

[Czech-it-Out Graphics]

i never use the masks even if i use the regular window lines, i hate the drips and stuff u get with those chitty masks and they never fit the lines right.

Out of a 16 oz bottle I can mask about 12 bodies with 5 coats

[Obsessive R/C]

What size tip do you use to spray it with? (what brand are you using?) the BD that I use seems like it would be way too thick to spray.

[Czech-it-Out Graphics]

I dont spray it, I also brush it on. I use the Parma stuff but it is identical in every way to BD. one thing that is important to put the stuff on with a clean brush. The only way that i have been able to clean a brush with this crap on it is to soak it in nitro. I know it sounds crazy but it works. rinse the brush off, get all the wet mask and stuff out then just drop it in a glass or jar filled with 30% nitro and voiala. make sure to thoroughly rinse out the brush again when taking it out. I do this in between every coat and it seems like less mask gets wasted