|
|
|
||||
|
||||
|
06-14-2006, 10:32 PM
My truggy was just as fast as my savage if not faster... I dont think a 2 speed adds that much on the top end... I think it just helps nitro engines build the torque they need down low with a lower ratio...
Im sure if you got those boas on youd be fine --Then follow the rules! haha!-- -Tune 
|
|
|
||||
|
||||
|
06-14-2006, 10:45 PM
Assuming you have a 46 tooth spur (stock kyosho) and a 16 tooth bell you are running a 2.8 ratio. Thats about 1.5 too low for runnign mt tires... I hope you have another $70 for a new clutch soon. Because you are going to smoke the clutch and over work your engine.....
But then again what do I know....LOL
|
|
|
||||
|
||||
|
06-14-2006, 11:07 PM
Quote:
1. You know where to shop for big hats. 2. You know how to get mad over someone leaving your sharpie out. 3. You know how to make R/C purchases without the wife knowing. 4. You know how to ride your tri-cycle when your drunk. 5. You know how to lay the power down !!! 6. You know how to embalm some fresh meat.
|
|
|
||||
|
||||
|
06-14-2006, 11:08 PM
Lmao
www.czech-it-out-graphics.com 1/29/07 never forget....TTT  Bringing old know-it-all blow hards back to reallity at a forum near you "Always Imitated, Never Duplicated"
|
|
|
||||
|
||||
|
06-15-2006, 01:59 AM
Quote:
Nuh unh!!! I got me some LSP ring and pinion gears so I can run this chit dude... 
|
|
|
||||
|
||||
|
06-15-2006, 09:06 AM
LOL
That is the rario at your clutch. Ask how many LSP drivers are running a 16t bell, and I bet zero. And we have your ring and pinions and a larger spur gear... I have a NR 528 and the most I ever ran was a 15. But like I said before what do I know, just trying to save you some aggrevation but you obviously know more.... 8^) So good luck!!!!!!!
|
|
|
||||
|
||||
|
06-15-2006, 11:32 AM
Quote:
|
|
|
||||
|
||||
|
06-15-2006, 11:45 AM
when u go to the track get some vid of that thing.
Racing from a roll is like beating off, it may be fun but its not the real thing. Quote:
|
|
|
||||
|
||||
|
06-15-2006, 11:50 AM
If I remember to. We're rolling up there around 6 and I want to run as much as possible before sundown.
|
|
|
||||
|
||||
|
06-15-2006, 01:45 PM
Hey, my foams came in! My boas are all glued up and ready to run tonight.
If I do take video, I'll post it up.
|
|
|
||||
|
||||
|
06-15-2006, 02:22 PM
Uh-oh. I had a run away. Got about 40ft and then re-gained power. Thankfully, it jumped a little curb and ended up in a person down the street's lawn, about a foot away from their SUV tire. That could have been bad. I don't know what could have went wrong though, everything that should be loc-tighted is, all plugs are secure in the receiver, and there's no binding w/ the servos in motion. Ideas? It ran fine afterwards, no glitches or anything.
Do you think that mabye the metal gears (clutch and spur) are causing interference?
|
 |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| TTR ST-1 Truggy build up! | Czech-it-Out Graphics | Racers Forum | 13 | 05-15-2006 12:26 AM |
| Mugen MBX Truggy (SOLD) | RobH | Buy / Sell / Trade | 11 | 02-20-2006 12:25 AM |
| Kyosho Mini Inferno ST TRUGGY | RCDad | Racers Forum | 1 | 09-19-2005 02:37 PM |
| Kyosho 7.5 Kanai 2 Truggy rolling chassis for sale! Pics | SixVi6-Camaro | Buy / Sell / Trade | 0 | 08-25-2005 05:47 PM |
| Kanai 2 buggy/truggy (SOLD) | cemeb4dk | Buy / Sell / Trade | 7 | 07-20-2005 03:09 PM |
lol
