|
|
|
||||
|
||||
|
03-31-2007, 06:00 PM
How do I get the sleeve out w/out scraping the shit out of it?
I was born under the hood of a 68 FastBack, Synthetic 10w-30 in my veins, 120 octane in my bottle, Nitrous Oxide for adrenalin and a Blower for a soother 
|
|
|
||||
|
||||
|
03-31-2007, 06:16 PM
have the head and backplate off. put the fat end of a zip tie threw one of the ports and use the piston to push it out. A heat gun will help if gummed up with old oil.
MBX5T - O.S. MBX5R - Novarossi Nomadio
|
|
|
||||
|
||||
|
04-02-2007, 08:58 AM
I took the backplate off, put a ziptie in the exhaust outlet through a port, and the sleeve isn't coming out?! (also tried heating it up)
I was born under the hood of a 68 FastBack, Synthetic 10w-30 in my veins, 120 octane in my bottle, Nitrous Oxide for adrenalin and a Blower for a soother
|
|
|
||||
|
||||
|
04-02-2007, 07:55 PM
Quote:
I was born under the hood of a 68 FastBack, Synthetic 10w-30 in my veins, 120 octane in my bottle, Nitrous Oxide for adrenalin and a Blower for a soother
|
|
|
||||
|
||||
|
04-02-2007, 07:59 PM
doesnt matter just turn it it will come up
www.czech-it-out-graphics.com 1/29/07 never forget....TTT  Bringing old know-it-all blow hards back to reallity at a forum near you "Always Imitated, Never Duplicated"
|
|
|
||||
|
||||
|
04-02-2007, 08:35 PM
Quote:
I was born under the hood of a 68 FastBack, Synthetic 10w-30 in my veins, 120 octane in my bottle, Nitrous Oxide for adrenalin and a Blower for a soother
|
|
|
||||
|
||||
|
04-02-2007, 08:55 PM
take some vice grips, put them on the flywheel (tightly) so they dont slip, and turn with all your might, heat it up if you want. if its really tight, it shouldnt hurt the sleeve, just indent the zip tie
Losi 8ight with v-spec
|
|
|
||||
|
||||
|
04-02-2007, 09:31 PM
If it's really tight, it'll snap the zip tie.
|
|
|
||||
|
||||
|
04-02-2007, 09:46 PM
siiiiigh.....
(these last like 5 or 6 posts remind me of the scene in the movie "2001 A space odyssey " Ya know when all the monkies figure out how too use tools) --Then follow the rules! haha!-- -Tune
|
|
|
||||
|
||||
|
04-02-2007, 11:45 PM
Quote:
On a side note: Got the piston, sleeve, and crank shaft out....How do I get the bearings out? I was born under the hood of a 68 FastBack, Synthetic 10w-30 in my veins, 120 octane in my bottle, Nitrous Oxide for adrenalin and a Blower for a soother
|
|
|
||||
|
||||
|
04-02-2007, 11:51 PM
heat it up so the case expands
Racing from a roll is like beating off, it may be fun but its not the real thing. Quote:
|
|
|
||||
|
||||
|
04-02-2007, 11:54 PM
its not that easy.
the best way to get them out really is with a bearing puller. you can just tap the front out but if u use the puller on the rear bearing its useless. you can put it in the oven at like 300 for 15 minutes or so and try tappin the case against a cutting board or something but i never was very succesfull in that lol www.czech-it-out-graphics.com 1/29/07 never forget....TTT Bringing old know-it-all blow hards back to reallity at a forum near you "Always Imitated, Never Duplicated"
|
how about you use some lube. like wd-40. its bound to come out.
