|
|
|
||||
|
||||
Finally went BL in the Mini-T -
07-08-2006, 03:40 PM
I like it
 I just got the 4200kv Mamba and it seems to run pretty good too.so you can see someone else getting screwed at the same time I went into the gas station today and asked for five dollars worth of gas......The clerk farted and gave me a receipt. 
|
|
|
||||
|
||||
|
07-08-2006, 06:20 PM
Sweett...Go get lipo and you'll have like hour long + runtimes.
|
|
|
||||
|
||||
|
07-09-2006, 10:21 AM
HS-55 servos, but I swapped up to a used 8000kv last night, I'm puting the 4200kv in my Mini-Giant crawler.
so you can see someone else getting screwed at the same time I went into the gas station today and asked for five dollars worth of gas......The clerk farted and gave me a receipt.
|
|
|
||||
|
||||
|
07-09-2006, 01:08 PM
The Losi one, it's only around $3.00, but I've heard of taking the top/output gear out of the stock servo and swapping with top/output gear of the HS-55 too.
so you can see someone else getting screwed at the same time I went into the gas station today and asked for five dollars worth of gas......The clerk farted and gave me a receipt.
|
|
|
||||
|
||||
|
07-12-2006, 06:37 PM
Cool......I just radared the truck with the 8000kv motor and a Losi 1100mAh pack with Deans Plugs and stock batt wires and gearing, 26mph average over 4 runs!
so you can see someone else getting screwed at the same time I went into the gas station today and asked for five dollars worth of gas......The clerk farted and gave me a receipt.
|
|
|
||||
|
||||
|
07-12-2006, 07:57 PM
Time for LIPO and get 50 + mph!!!
|
|
|
||||
|
||||
|
07-13-2006, 10:30 AM
I suprised the stock type gear diff has stood up sofar, I'm guessing the out of box programming on the ESC and the HPI 100000# grease may have something to do with it.
so you can see someone else getting screwed at the same time I went into the gas station today and asked for five dollars worth of gas......The clerk farted and gave me a receipt.
|
|
|
||||
|
||||
|
07-13-2006, 01:14 PM
Quote:
|
|
|
||||
|
||||
|
07-13-2006, 03:47 PM
friggin' pinion gears........
I've tried the Trinity ones because they had a setscrew, but the screw keeps coming loose and getting jammed in the motor mount screw in less than 10 minutes of running, so I put a stock (Maybe the factory original, I'm not too sure on that though) pinion gear on and it's started to slide off after about 10 minutes and now will barely hold on for more than a few minutes. I'm about ready to break out the tire glue...errrrrrrrrrrrrrrrr  so you can see someone else getting screwed at the same time I went into the gas station today and asked for five dollars worth of gas......The clerk farted and gave me a receipt.
|
|
|
||||
|
||||
|
07-13-2006, 04:01 PM
ive used CA on there before, but be careful, one time on a brand new motor I got the pinion wouldn't say on so I put thin glue on there and it just traveled the shaft and locked it up, it took me like 4 hours of spinning the shaft with needle nose and then running like 5 or 6 packs thru it with the motor just sitting on the table before it finally lossened up.
ALL RC STUFF FOR SALE. PM FOR DETAILS.
|
|
|
||||
|
||||
|
07-13-2006, 04:39 PM
Thanks, I'll make sure that if I do, the truck will be laying on the right side.
so you can see someone else getting screwed at the same time I went into the gas station today and asked for five dollars worth of gas......The clerk farted and gave me a receipt.
|
|
|
||||
|
||||
|
07-13-2006, 08:52 PM
Or use a medium/thick CA that won't seep thru the pinion.
|
|
|
||||
|
||||
|
07-14-2006, 11:35 AM
Got 28 mph hour out of it yesterday, clocked it in a 25mph zone with one of those radar trailers, anywhere above 25mph it flashes your speed in red. Wish I had atleast a camera operator with me....................
so you can see someone else getting screwed at the same time I went into the gas station today and asked for five dollars worth of gas......The clerk farted and gave me a receipt.
|
